Just How to Remove as well as Replace a Bath Tub.
Just How to Remove as well as Replace a Bath Tub.
Blog Article
Just how do you feel in regards to Installing A Bathtub?
Mounting a bathtub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is likewise a moderately hard job. If the old bathtub is easily available, the task can move rapidly; if you have to open a wall surface to get rid of the old tub and place the brand-new tub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to leave the old tub as well as embeded in the brand-new one. Make certain you have actually certified yourself for the work and are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you might need an expert plumber to make tube links.
This write-up will help you set up a brand-new bathtub in your shower room if you have actually already bought a new tub as well as do not require to alter the arrangement of your previous water pipelines.
Your tools as well as material checklist ought to comprise the following:
Getting ready for the Setup
First of all, the sustaining framework provided with the bathroom should be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its last setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the restricted gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly come from the pipes. Once the supply pipelines have been gotten rid of, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, put the bath tub in the called for setting. The wood boards are handy in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the level and changing the feet on the bath tub up until the spirit level reads degree.
To mount taps, fit the bottom of the furthest flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Activate the supply of water and inspect all joints and also new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub must wait till the bathtub has actually been utilized at the very least once as this will settle it right into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap as well as the sink. Protect the tap in position with the manufacturer offered backnut. When the tap is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former type ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a stiff seal, causing the water to penetrate the wall surface between the bath and the tiling, bring about problems with wetness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes and cartridges, and also can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly load the tub with water before securing, to enable the movement experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were brought to that report about How to Install a Bathtub through a friend on our other domain. Do you know someone else who is inquisitive about the subject? Feel free to share it. I enjoy reading our article about How to Install a Bathtub Yourself.
Estimate Free Report this page